Panier (0)
Standard

IEEE 2833-2024

Actuel

Note: Actuellement en cours d'élaboration: IEEE 2833-2024

Aperçu

Amendements et versions existants ou nouveaux doivent être achetés séparément.

Langue
Format

Résumé

New IEEE Standard - Active. The technical requirements for overhead transmission lines with composite insulated crossarm (CICA) supports, which include design and functional provisions; component requirements; tests; installation and acceptance needs; and operation and maintenance procedures are specified in this Guide.

Spécifications des produits

  • Standard de IEEE
  • Publié:
  • Type de document: IS
  • Pages
  • Editeur: IEEE
  • Distributeur: IEEE
  • Comité national: IEEE Power and Energy Society / Transmission and Distribution
  • ICS: 29.240.20

Relations produit

  • Référence: IEEE C62.82.2-2022
  • Référence: IEEE 1862-2014
  • Référence: IEEE 4-2013
  • Référence: IEEE 4-2013
  • Référence: IEEE 1243-1997
  • Référence: EN 50341-1, Overhead electrical lines exceeding AC 1 kV--Part 1: General requirements--Common specifications.
  • Référence: CISPR TR 18-2, Radio interference characteristics of overhead power lines and high-voltage equipment--Part 2: Methods of measurement and procedure for determining limits.
  • Référence: ANSI/AISC 360, Specification for Structural Steel Buildings.
  • Référence: IEC 60060-1, High-Voltage Test Techniques--Part 1: General Definitions and Test Requirements.
  • Référence: IEC 61109, Insulators for overhead lines--Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1 000 V--Definitions, test methods and acceptance criteria.
  • Référence: IEC 62631-3-1, Dielectric and resistive properties of solid insulating materials--Part 3-1: Determination of resistive properties (DC methods)--Volume resistance and volume resistivity--General method.
  • Référence: ISO 604, Plastics--Determination of compressive properties.
  • Référence: ISO 14125, Fibre-reinforced plastic composites--Determination of flexural properties.
  • Référence: ISO 34-1, Rubber, vulcanized or thermoplastic--Determination of tear strength--Part 1: Trouser, angle and crescent test pieces
  • Référence: IEC/TS 60815-3, Selection and dimensioning of high-voltage insulators intended for use in polluted Conditions--Part 3: Polymer insulators for a.c. systems.
  • Référence: ASCE/SEI 10, Design of Latticed Steel Transmission Structures.
  • Référence: IEC 60826, Design criteria of overhead transmission lines.
  • Référence: IEC 61952, Insulators for overhead lines--Composite line post insulators for A.C. systems with a nominal voltage greater than 1 000 V--Definitions, test methods and acceptance criteria.
  • Référence: ANSI C29.12, American National Standard for Composite Insulators--Transmission Suspension Type.
  • Référence: ISO 2781, Rubber, vulcanized or thermoplastic--Determination of density.
  • Référence: IEC 61284, Overhead lines--Requirements and tests for fittings.
  • Référence: ASTM D695, Standard Test Method for Compressive Properties of Rigid Plastics.
  • Référence: IEC 60587, Electrical insulating materials used under severe ambient conditions--Test methods for evaluating resistance to tracking and erosion.
  • Référence: IEC/TR 62039, Selection guidelines for polymeric materials for outdoor use under HV stress.
  • Référence: IEC 60071-2, Insulation co-ordination--Part 2: Application guidelines.
  • Référence: CIGRE TB 555, Artificial pollution test for polymer insulators.
  • Référence: ISO 62, Plastics--Determination of water absorption.
  • Référence: IEC 60243-1, Electric strength of insulating materials--Test methods--Part 1: Tests at power frequencies.
  • Référence: ANSI C29.17, American National Standard for Composite Insulators--Transmission Line Post Type.
  • Référence: IEC/TS 62073, Guidance on the measurement of hydrophobicity of insulator surfaces.
  • Référence: IEC 61462, Composite hollow insulators--Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V--Definitions, test methods, acceptance criteria and design recommendations.
  • Référence: CIGRE TB 691, Pollution test of naturally and artificially contaminated insulators.
  • Référence: IEC 61467, Insulators for overhead lines--Insulator strings and sets for lines with a nominal voltage greater than 1 000 V--AC power arc tests.
  • Référence: IEC 60507, Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems.
  • Référence: IEC 62217, Polymeric HV insulators for indoor and outdoor use--General definitions, test methods and acceptance criteria.
  • Référence: IEC 60437, Radio interference test on high-voltage insulators.
  • Référence: CIGRE TB 63, Guide to procedures for estimating the lightning performance of transmission lines.
  • Référence: IEC 60652, Overhead line structures--Loading tests.
  • Référence: ISO 527-4, Plastics--Determination of tensile properties--Part 4: Test conditions for isotropic and orthotropic fiber-reinforced plastic composites.
  • Référence: IEC 60383-2, Insulators for overhead lines with a nominal voltage above 1000 V--Part 2: Insulator strings and insulator sets for a.c. systems--Definitions, test methods and acceptance criteria.
  • Référence: ISO 37, Rubber, vulcanized or thermoplastic--Determination of tensile stress-strain properties.