Standard

IEC 60335-2-34:2024 ED7

Aktuell

Bestehende oder zukünftige Amendments und Versionen müssen separat erworben werden.

Sprache
Format

Zusammenfassung

IEC 60335-2-34:2024 deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that can be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 600 V for multi-phase, 600 V direct-current (DC) motor-compressors. This standard also covers: – multi-speed motor-compressors, that are motor-compressors, the speed of which can be set to different values; – variable capacity motor-compressors that are motor-compressors where the capacity of the compressor is controlled at fixed speeds. Examples of equipment which contain motor-compressors are: – tumble dryers (IEC 60335-2-11); – refrigerating appliances, ice-cream appliances and ice-makers (IEC 60335-2-24); – electrical heat pumps, air-conditioners and dehumidifiers (IEC 60335-2-40); – commercial dispensing appliances and vending machines (IEC 60335-2-75); – commercial refrigerating appliances and ice-makers with an incorporated or remote refrigerant unit or compressor (IEC 60335-2-89); – refrigerating equipment for measurement, control, and laboratory use (IEC 61010-2-011); – professional ice-cream makers (IEC 60335-2-118); – professional systems and heat pumps (ISO 5149-2); This standard does not supersede the requirements of standards relevant to the particular appliance in which the motor-compressor is used. However, if the motor-compressor type used complies with this standard, it will not be necessary for the tests for the motor-compressor specified in the particular appliance standard to be made in the particular appliance or assembly. If the motor-compressor control system is associated with the particular appliance control system, additional tests could be necessary on the end product. So far as is practical, this standard deals with the common hazards presented by motor-compressors used in appliances which are encountered by all persons in and around the home. However, it does not in general take into account: – the use of appliances by young children or infirm persons without supervision; – playing with the appliances by young children. Attention is drawn to the fact that: – for motor-compressors intended to be used in appliances in vehicles or on board ships, additional requirements could be necessary; – motor-compressors used in appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas), additional require¬ments could be necessary; – in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. This standard does not apply to – motor-compressors designed exclusively for industrial purposes. This seventh edition cancels and replaces the sixth edition published in 2021. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment with IEC 60335-1:2020; b) in the scope added the rating up to 600 V (Clause 1); c) the definition of design pressure has been changed in maximum allowable pressure (3.1.101, 7.102, 22.7); d) introduction of maximum load conditions (MLC) as declared by the manufacturer (3.1.103, 5.6, 7.12, Annex AA); e) transcritical back pressure categories (R-744) have been introduced (3.1.102, Table AA.1, Table AA.2); f) new definition of coilette has been introduced (3.8.103); g) new definition of bypass valve has been introduced (3.8.104); h) the evaluation of motor-compressors using a motor-compressor control system has been clarified (6.101, 6.103, 6.104, 19.1); i) modification of electric strength test has been added (16.2); j) reference to the fatigue test has been deleted (Clause 18); k) compliance for pressure tests has been updated (22.7, Annex EE); l) reference for the motorette has been transferred from Annex BB to the new Annex FF; m) annex for insulation materials and parts has been updated and tie cord relaxation has been removed (Annex CC); n) new annex for motorette or coilette has been introduced (Annex FF). This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.

Produktspezifikationen

  • Standard von IEC
  • Ausgabedatum:
  • Edition: 7
  • Dokumenttyp: IS
  • Seiten
  • Herausgeber: IEC
  • Lieferant: IEC
  • ICS: 97.040.30
  • Internationales Komitee: TC 61/SC 61C

Produktbeziehungen

Produktlebenszyklus